5.0 out of 5 stars Quick bonding

A.C. · 20 August 2025

Unbelievable how quickly it bonded metal, gorilla glue takes 10 to 15 minutes to bond and came undone but this glue bonded in 20 seconds! Be careful!

4.0 out of 5 stars Glue

A.C. · 15 July 2025

Bought this to stick handle on a metal cup did not work but good for other things

5.0 out of 5 stars Fantastic stuff and strong (2 x repairs done with it so far)

H.U.R. · 27 November 2022

This 2 part metal glue which is easily used by pushing the plungers, extruding the adhesive and hardener for mixing into a glue paste is exceptionally strong and works a treat for metal surfaces.I had a slight leak on a copper pipe connection so after isolating the water supply and drying the surface out thought I'd give this a go to see if it can carry out a temporary repair to stop the dripping (I tried tightening the nuts and replace the olives but nothing worked so until I get a chance to replace the pipework and connection this glue will do the job)I left the applied paste for just over 24hours and anxiously turned the water supply back on to see if my efforts had paid off. No drips :-)This was on a cold water supply pipe to the loo, so I'm not sure how it would cope with hot water pipes such as radiator pipes and the like but it certainly repaired the leaking joint on the cold pipe.I'd say the price is right for this type of glue and use is very easy with some accessories supplied to aid mixing such as wooden sticks and gloves.Always wear gloves when working with adhesive.I like these syringe dispensing systems as provided you push evenly on the plunger you virtually always get equal parts and the glue left over inside the tubes tends to keep for some time ready for the next repair.Working time with this stuff is also really good and gives you plenty of time to work with it until it begins hardening and curing.I would definitely buy this again and impressed with the ease.Review update 17th October 2023I had to update my review and really give this metal glue a further thumbs up for its next job that I used it for.I had a blowing exhaust on my car, a small hole in one of the connection points about an inch in length by about 5mm wide and I used this to block the hole up.I mixed the parts equally again and applied to the hole in the exhaust and allowed it to dry for 24hrs.A week later and the glue is still holding strong and stopping the exhaust from blowing despite it being under constant high temperatures and weathering etc.This repair was done to the back end of the exhaust system near the back boxes and has done a great job at bridging the crack/hole until I get round to repairing that part.Brilliant stuff and I'll definitely purchase this again when needed.Quick review update: 18th March 2024:Needed to use some more of this on the exhaust again to help block a hole on the exhaust and the glue was ready to use so has kept well under normal storage conditions (was about 3/4 tubes left)Make sure you clean both ends of the caps before storing and you shouldn't have any issues when you come to using it again. Great stuff and I'll be buying this again.

5.0 out of 5 stars Mended a broken pressure cooker handle and holding strong

E. · 25 November 2022

My trusty ancient pressure cooker is broken.The handle has broken right off with no way to put it back.The fixing for the handle is a steel rod and steel bolt but the rod has worn away enough that the bolt no longer holds onto it and cant be got out either.I saw this metal to metal glue and thought it would be a very good challenge for it.Firstly will it hold it back together enough to make it useable again?Yes it is holding strong!Secondly will it cope with getting hot?So far so good..Lastly will it cope with being washed?No problem with getting it wet .Saved me a goodly sum over getting another pressure cooker and saved my trusty pan.You get the double tube with plunger, mixing card, two wooden mixing sticks and a pair of plastic gloves.The stuff pushes out of each hole evenly and you mix it.Then there is a 20 minute using window.Parts to be stuck must be clean so some wire wool and a wire brush are a good thing to use to get the surface as stable as possible .Its cured in 5 hours (feels hard and dry)but they recommend 24 hours till using .I managed to get a glob of glue up into the end and also glued the sleeve bit back in place with a bead of glue squidged out all round.It is possible to shut the rest of the glue back in to keep for another use.I stuck one of the gloves in under the closing cap so that when opening again, if it glues shut (as has happened with epoxy glues in the past) I can still get the cap off.Would recommend this, it is easy to use, not overpoweringly smelly and does the job.

5.0 out of 5 stars Very reliable bonding!

S. · 26 November 2022

I live by myself and my two adored cats. I am blessed to have a vast garden; therefore, much work 😊. As I am very independent and solution-orientated, I tend to do most of the handy work around my home and garden and not wait or beg my landlord to come and do things. I have changed my faucets, unblocked my drains, taken apart the kitchen sink and pipe, changed the glass on my stove, and even some woodwork.This adhesive is a brilliant addition to my handywoman toolset. It is very reliable, and I genuinely appreciate that I can squeeze out a 1:1 ratio from both tubs. Mixing a two-part adhesive can get tricky as you might not get that precise ratio from mixing two. Moreover, the tiny pack contains a mixing tray, two wooden mixing sticks, and gloves. I love it when your needs are anticipated and resolved.Being slightly cheesy, this adhesive supports my independence and delivers excellent results. The bonding is brilliant and lasts. I have so many little jobs to do with it that I will order some more as now I know what a reliable product it is. I am happy to recommend this glue as it made my life easy and the bonding strong 😊!

4.0 out of 5 stars A good metal glue easy to dispense and mix

D.C. · 2 December 2022

I'm a big fan of araldite and prefer a two mix epoxy to any other glue.This is similar in design and being a plunger type makes it easy to extract the same quantity of resin and hardener at the same time. It seems to dry reasonably quickly and the bond is very strong.I'm not so impressed with the tube design. The plunders are separate rather then coming as part of the tubes. And I feel that the two nozzles are too close to each other. Although there's a twist top which can only be put on the correct way round, a little epoxy or hardener that leaks to the other tube opening will likely result in a top that bonds permanently. So extra care has to be taken to ensure both nozzles are clear before replacing the top.Plastic gloves, a couple of mixing sticks and a mixing board make up the kit.Overall pretty decent.