5.0 out of 5 stars Very versatile mobile vise

D. · 10 September 2024

(function() { P.when('cr-A', 'ready').execute(function(A) { if(typeof A.toggleExpanderAriaLabel === 'function') { A.toggleExpanderAriaLabel('review_text_read_more', 'Read more of this review', 'Read less of this review'); } }); })(); .review-text-read-more-expander:focus-visible { outline: 2px solid #2162a1; outline-offset: 2px; border-radius: 5px; } This vise is very nice for the price, it's very smell but very sturdy with a solid design.First glance: I noticed the ball joint, threaded rod, and guide pins were quite dry with a very light machine oil applied so I disassembled the unit degreased it then liberally coated the metal on metal contact points, the ball joint, the threaded rods, and the guide pins with moly grease:1. Unscrewing the threaded rod all the way releases the front jaw half.2. Using a size 2 slotted screwdriver you can gently pry the circlip from the threaded rod shaft which releases the threaded rod from the jaw assembly.3. Unscrewing the smaller spring/washer retained bolt and the two larger phillips screws frees the ball joint clamp assembly.There is no bushing or bearing to take the load of the guide pins so i filled the jaw half cavities with moly grease and after assembling the unit i wiped off all the excess that built up and degreased the jaw halfs so now the unit is built more accordingly to last a lot longer.I'm looking into designing some bushings and guide pin bearings to print with my 3d printer to see if i can make the jaws stay aligned and not wobble.Overall its a great vise and i've needed a vise for decades but dont have a proper solid table that would be suited for bolting a big solid vise, this is a hobby vise that is mobile and is perfect for my airsoft gunsmithing.5/5 would recommend to anyone, I'd also suggest mirroring my actions to degrease clean and grease the unit with a proper grease designed for metal on metal contact that will reduce wear ultimately prolonging the longevity of the vice, I know it's only £22 but a bit of rust or uneven wear or galling would ruin things quickly.

5.0 out of 5 stars Versatile Grip: A Review of the STANLEY MAXSTEEL Multi Angle Vice 🔧💪

R.G. · 8 April 2024

Versatile Grip: A Review of the STANLEY MAXSTEEL Multi Angle Vice 🔧💪As a DIY enthusiast and craftsperson, having a reliable, versatile vice is essential for my workspace. When I came across the STANLEY MAXSTEEL Multi Angle Vice, I was immediately intrigued by its claims of 360-degree rotation and locking capabilities. After putting this vice through its paces, I'm ready to share my thoughts.Positives:• The durable, corrosion-resistant cast-iron construction of this vice instills confidence, knowing it can handle a wide range of clamping and holding tasks without fear of damage or wear. 💪• The patented ball joint design allows for full 360-degree rotation and locking at any angle, making it incredibly versatile and adaptable to my specific needs. This is a game-changer for access and positioning. 🔄• Many customers, including myself, have praised the compact and lightweight nature of the vice, making it easy to transport and store without sacrificing strength or stability. 🏠Potential Drawbacks:• While the removable rubber jaw pads protect delicate surfaces, a few users have reported that they can occasionally slip or become dislodged during use. Proper maintenance and care are important. 🧠• The bright yellow and black color scheme, while visually appealing, may not suit everyone's workshop aesthetic preferences. 🎨As a customer who has been using the STANLEY MAXSTEEL Multi Angle Vice, I can say that it's a fantastic tool for a wide range of projects. The 360-degree rotation and locking mechanism make it incredibly versatile, allowing me to position the vice exactly where I need it for maximum accessibility and convenience. The cast-iron construction is impressively durable, and the compact size makes it easy to store and transport. While I've occasionally had to readjust the rubber jaw pads, the overall quality and performance of this vice have been excellent. I highly recommend it to anyone in need of a reliable, flexible clamping solution for their workshop or craft space.Overall, the STANLEY MAXSTEEL Multi Angle Vice has proven to be an invaluable addition to my workspace. The impressive range of motion, durable construction, and compact design make it a versatile tool that can handle a wide variety of clamping and holding tasks with ease. 🌟 While the occasional minor issue with the jaw pads is worth noting, the vice's overall performance and capabilities firmly cement it as a top-notch choice for DIY enthusiasts and craftspeople alike.

4.0 out of 5 stars Vice dilemma!

I.J. · 28 February 2013

This is not an easy one!The good stuff includes the design & the price, but there are some issues that really should not be there!The design really is excellent and it such a shame that the dismal quality control doesn't live up to it. As delivered, my example works OK (and in fairness for much hobby use and at this price point that's fine) but with a little more care in manufacture it could be so much better!Issues:- the jaws do not close properly or evenly. If I close them on a sheet of 90gm A5 paper, one side locks up hard under medium tommy bar pressure but the other side is free to slide freely between the jaws. Also the jaws are misaligned - the top and end surfaces do not sit level with their mating jaw. Both of these faults are due to the fact that one jaw has one of its fixing holes drilled & tapped off centre. In addition, the casting on which the jaw seats has not been cleaned up properly - it is gunged up with paint and there are casting marks that stand proud of the surface that prevent the jaw seating correctly.- the cover that sits over the ball joint is a very poor fit - it looks like the ball itself is either too big for the cavity in which it sits, or the cavity casting has not been cleaned and dressed correctly. I haven't had time to look into this yet, but it probably isn't irreparable or mission critical.I suppose the best way to look at this tool is as a kit of parts from which it is possible to make a very decent and versatile vice (that's why I've given it 4 stars). It is a relatively simple matter to clean up the top casting and make up a new set of jaws that will close properly. I'll probably make up an aluminium set and/or a nylon set whilst I'm at it.For less than £20 it's not a bad set of parts, on the other hand, I didn't know I was buying a kit....Bottom line, Stanley: spend the time and effort that you wasted on silly packaging on a bit of QC and you'd have a much better product for no additional cost!

Très bien pour ça taille et articulé

R. · 16 June 2025

(function() { P.when('cr-A', 'ready').execute(function(A) { if(typeof A.toggleExpanderAriaLabel === 'function') { A.toggleExpanderAriaLabel('review_text_read_more', 'Read more of this review', 'Read less of this review'); } }); })(); .review-text-read-more-expander:focus-visible { outline: 2px solid #2162a1; outline-offset: 2px; border-radius: 5px; } Petit étau c'est ce que je voulais . Attention il est petit et fait pour de la toutes petites bricole ce n'est pas un étau d atelier mécanique !!! Donc pour ça taille il est solide et l articulations fonctionne bien . Pour la livraison la poste c'est catastrophique le livreur dit qu'il est passé alors que j étais présent et j'ai vu personne !!! C'est une honte se que c'est devenu la poste . Mais ça ni le vendeur ni Bolo y peuvent quelque chose.

E' un "must have" per i coltellinai!

o. · 25 April 2025

Mi serviva una morsa che potesse ruotare a 360° ed in tutte le angolazioni e questa è davvero ottima e progettata bene! Io l'ho comprata perchè la uso come morsa per la costruzione di coltelli artigianali, nello specifico per fare rifinizione dei manici. E' comodissima perchè posso adattarla in base alle mie esigenze e angolazioni. Nella scatola sono disponibili anche dei copri ganasce in silicone, in modo che durante il serraggio, la zigrinatura della morsa non vada ad intaccare il pezzo che si sta lavorando. Nel complesso è molto robusta e si vede che è professionale, non saprei però come si può comportare con lavori pesanti tipo di carpenteria, edilizia ecc.. Per lavori di rifinizione come nel mio caso è davvero eccellente.Sono super soddisfatto!

Çok kaliteli

M.O. · 22 April 2025

Harika bir alet

praktisch für kleine Werkstücke und mobiles Arbeiten

H. · 2 June 2025

dieser kleine "Schraubstock" dient mir als "dritte Hand" und zum Fixieren kleinerer Werkstücke.Nach dem Auspacken etwas Maschinenfett auf die Gewindestangen und einmal ganz zu- und wieder aufgedreht - dann hat sich das Fett gut verteilt und die Gewindestangen laufen weich.Mittels der Tischbefestigung ist das Teil schnell da, wo es gebraucht wird, angebracht (festgeschraubt), wobei man lediglich durch die Spannöffnung der Klemmzwinge hinsichtlich der Dicke der Tischplatte (o.ä.) limitiert ist.Entgegen meiner ersten Befürchtung, dass die Fixierung des Kugelgelenks nicht wirklich hält, muss ich sagen, dass -wenn man die Klemmvorrichtung ordentlich festzieht- der Aufbau mit den Spannbacken tatsächlich fixiert bleibt. Ist nun kein Ersatz für einen "richtigen" Schraubstock oder eine Vorderzange (am Hobeltisch), aber für kleinere und insbesondere mobile Arbeiten geeignet. Insbesondere finde ich die 3-D Beweglichkeit (dank des Kugelgelenks) des Spannbacken-Aufbaus sehr hilfreich - Werkstück einspannen, gewünschte Position einstellen und den Kugelgelenk fixieren - fertig.Ich bin zufrieden damit - daher von mir volle 5 Sterne.

Bardzo fajne imadło

K.J. · 21 February 2023

Dobrze wykonane imadło, zapewniające stabilizację obrabianego przedmiotu. Wystarczająco szeroki rozstaw szczęk, super opcja pracy pod dowolnym kątem. No i ładne to jest. Da się przykrecić wszędzie. Polecam.